Skip to content
Licensed & insured Family owned & operated · Lakeville, MA
No heat? Tap to call508-521-9477
Hydronic piping installation: copper main with a balancing valve and an orange motorized actuator in a commercial building
Licensed & insured · Lakeville, MA

Radiant Heating Brands We Service

A radiant system is built from parts by several manufacturers: tubing, manifolds, pumps, valves, controls and the boiler. Armus Mechanical, based in Lakeville, services boiler-fed radiant systems across New Bedford and the SouthCoast, whichever brands are in your basement. This page lists the brands we work with and how we handle one we do not recognize.

  • Same-day repair
  • Free estimates on new systems
  • Financing through Wisetack
  • Warranty on our labor
Chat with ArmusOnline 24/7 · tap a topic to start

Boiler banging, leaking or not firing? Tell me what's going on.

At a glance

Service area
New Bedford, Lakeville and the rest of the SouthCoast, plus the South Shore, Cape Cod and Rhode Island
Based in
Lakeville, MA. We come to your home or business.
Phone
508-521-9477, answered 24/7
Specialties
Boiler-fed radiant systems and hydronic parts from many manufacturers: tubing, manifolds, pumps, valves and controls
Pricing
Repairs start with a paid diagnostic visit. Replacements get a free written estimate.

Which radiant brands do you service?

We service the parts of a radiant system by type, and these are the makers whose parts we handle.

Tubing, fittings and manifolds

Uponor, Viega, Rehau, Watts and Roth make radiant tubing, fittings and manifolds. We service the manifold, the balancing valves and the fittings we can reach, and we replace parts that have failed.

Circulator pumps and zone valves

Taco and Grundfos make circulator pumps, and Taco also makes zone valves. We test, replace and size pumps and valves for the loop they serve, and a recent job replaced a Taco zone valve actuator.

Valves, air separators and fittings

Caleffi makes valves, air separators and manifold parts used in hydronic systems. We service and replace them with the design of the system in mind.

Controls and thermostats

Tekmar and Honeywell make controls for mixing, zoning and outdoor reset. We service and set up the controls, and replace them when parts are no longer available.

Boilers that feed radiant floors

Radiant floors are fed by gas and oil boilers, condensing and non-condensing. Our boiler repair and installation page lists the boiler brands we work on.

A brand not on this list

If your system uses another manufacturer, we look at it on site and tell you what service it needs. The main question for older or discontinued equipment is whether parts are still available.

How to identify your brands

Look for the label on the manifold, the nameplate on each pump, the model label on the controls and the rating plate on the boiler. Photos of those labels help us arrive with the right parts, and you can attach up to five photos when you tap Book ASAP.

How do I know a radiant part needs replacing?

Any of these means a part may need replacing.

  • A pump that is loud, overheating or not moving water
  • A zone valve motor that hums but does not open or close
  • A manifold with corrosion, crusty buildup or weeping fittings
  • A control that has lost its settings or shows a fault
  • A mixing valve that sticks, leaving floors too hot or too cold

Repair a part or replace a discontinued one?

Repair a part when the manufacturer or a compatible maker still supplies it. Replace it when it is discontinued or keeps failing.

Usually a repair

  • A part that is still available from the manufacturer or has a compatible replacement
  • A control that can be reset or reprogrammed

Usually time to replace

  • A part that is discontinued with no compatible replacement
  • A pump or valve far past its life that keeps failing
  • Controls that can no longer be matched to the rest of the system

Compatible replacements often exist across brands, and we tell you what fits before we order.

Job photos

Hydronic & Radiant Heat: job photos

Real jobs, photographed by the technician who did the work.

Boiler circulator replacement: new green circulator pump on the same piping beside the boiler
Old red circulator pump on rusty iron piping before boiler circulator replacement
Before After
Boiler circulator replacement: new pump on the same piping
Radiant heat replacement: new multi-loop manifolds with a controller board on the same plywood wall
Old radiant manifolds and mixing station on a plywood wall before radiant heat replacement
Before After
Radiant heat replacement: new manifolds on the same wall
Radiant heat installation: new copper piping with a mixing valve and gauge on a basement wall
Radiant heat installation: copper piping with mixing valve
Radiant heating manifold installation: manifold with gauges and PEX loops on a plywood panel
Radiant heating manifold with gauges and PEX loops
Radiant heat installation: copper press piping with a mixing valve and circulator pump
Radiant heat installation: press piping, mixing valve and pump
Radiant heating manifold installation: two-loop manifold with red PEX tubing and blue valves
Radiant heating manifold: two loops with red PEX
Radiant heating manifold installation: black manifold with gray PEX tubing and a circulator pump
Radiant heating manifold with PEX tubing and circulator pump
Baseboard heat repair: burst copper pipe at the end of a finned-tube baseboard heater
Baseboard heat repair: burst copper pipe at a baseboard heater

How does a visit work, and what does it cost?

Diagnostic. Radiant repairs start with a paid diagnostic visit. We identify the parts, find the cause and give you the repair price in writing before any work starts.

Estimate. A replacement boiler gets a free written estimate, and so does a new radiant job. See our radiant heating cost page for how the estimate works.

What to have ready.

  • Photos of the manifold, pump labels, control labels and the boiler’s rating plate
  • What the system is doing, and which zones are affected
  • Anything you know about who installed it and when

Book online. You can book a visit online: send the form, and we confirm your visit by text. If your heat is out, call 508-521-9477.

Rebates & financing

Mass Save Heat Pump Installer Network participating contractor.

Rebates and the 0% HEAT Loan available.

Financing through Wisetack

Financing for new systems runs through Wisetack via Housecall Pro, subject to credit approval. Estimates on new systems are free.

Recent radiant parts jobs

From our completed jobs, most recent first. Customer names and street addresses are left out.

  • July 2026, Provincetown. Taco zone valve: Replaced a failed zone valve actuator on a geothermal heat pump loop.

Where do you service radiant systems?

We work in Lakeville, New Bedford, Middleborough, Dartmouth, Fall River, Taunton, Wareham, Brockton, Fairhaven, and the rest of the SouthCoast, South Shore, Cape Cod and Rhode Island. See all service areas.

Brands

Brands we service · Radiant Heating

  • Uponor
  • Viega
  • Watts
  • Rehau
  • Roth
  • Taco
  • Grundfos
  • Caleffi
  • Honeywell
  • Tekmar
Oil boiler tune-up: combustion analyzer connected to the boiler
Keep it running

Add it to a maintenance plan

Seasonal tune-ups keep your boiler efficient and catch small problems before the first freeze.

See maintenance plans

Radiant brand questions, answered

Can you work on a system with mixed brands?

Yes. Most radiant systems mix brands, with tubing from one maker, pumps from another and controls from a third. We service the system as a whole.

Can you replace a discontinued pump or valve?

Usually. Many pumps and valves have compatible replacements from other makers, and we confirm that the replacement fits the flow and pressure the loop needs before we order it.

Do I need to know my brands before I call?

No. Describe what the system is doing and send photos of the labels if you can. We identify the parts at the visit.

What controls do radiant systems use?

Most use zone thermostats with zone valves or circulators, plus a mixing control that keeps the floor water at the right temperature. Some add outdoor reset, which lowers the water temperature as the weather warms.

Radiant system problem?

Schedule radiant heating service in New Bedford & the SouthCoast

Call 508-521-9477, answered 24/7, or tap Book ASAP and the office confirms your visit by text.

Tap to call508-521-9477 Book ASAP
Book ASAP