Skip to content
Licensed & insured Family owned & operated · Lakeville, MA
No heat? Tap to call508-521-9477
Hydronic piping installation: copper main with a balancing valve and an orange motorized actuator in a commercial building
Licensed & insured · Lakeville, MA

Radiant Floor Heating Repair & Installation on the SouthCoast

Radiant floor heating warms the floor, and the floor warms the room, with no air blowing. Armus Mechanical, based in Lakeville, installs, repairs and maintains boiler-fed radiant systems across New Bedford and the SouthCoast. This page maps the radiant topics, and the three pages under it go deeper on how the systems work, what they cost and the brands we service.

  • Same-day repair
  • Free estimates on new systems
  • Financing through Wisetack
  • Warranty on our labor
Chat with ArmusOnline 24/7 · tap a topic to start

Boiler banging, leaking or not firing? Tell me what's going on.

At a glance

Service area
New Bedford, Lakeville and the rest of the SouthCoast, plus the South Shore, Cape Cod and Rhode Island
Based in
Lakeville, MA. We come to your home or business.
Phone
508-521-9477, answered 24/7
Specialties
Boiler-fed radiant floor heating: installation, repair and maintenance, including zone and manifold service and upgrades
Pricing
Repairs start with a paid diagnostic visit. Replacements get a free written estimate.

Where should I start with radiant heating?

Pick the page that fits your question. Each one covers a different part of radiant heat.

What radiant heating problems do you repair?

We repair the boiler-fed parts of a radiant system: the boiler, pumps, valves, manifolds, mixing valves and controls.

Cold or uneven floors

Patchy heat usually traces to air in a loop, an unbalanced manifold or a stuck mixing valve. We check supply temperature and flow at the manifold before we replace anything.

A zone that will not heat

A single dead zone is usually a zone valve or actuator, a thermostat or a circulator. We test each in turn and replace only the part that failed.

Gurgling, clicking or rushing water sounds

Air trapped in a loop is the usual cause, and it also starves the floor of heat. We purge the loop and look for where the air is coming from, such as a failing air separator or low pressure.

Boiler short cycling or low pressure

A boiler feeding low-temperature floors can cycle often when the controls are set wrong or the expansion tank has failed. We check the pressure, the expansion tank and the control settings.

Leaks at the manifold, pump or valves

We repair or replace leaking fittings and parts we can reach. If you suspect a leak in the floor loops themselves, call us and we will tell you what can be done after we see the system.

What do you assess before installing or upgrading radiant heat?

A radiant job starts with the floor and the heat loss, not the boiler. We install, repair and maintain boiler-fed radiant floors.

Floor construction and covering

The slab, subfloor and finish floor decide how the tubing goes in and how much heat reaches the room. Tile, stone, concrete and engineered wood work well, and thick carpet with heavy padding slows the heat down.

Heat loss

We calculate each room’s heat loss so the tubing spacing and water temperature match what the room needs. Insulation and windows change the answer.

Heat source

We check whether the existing boiler can feed low-temperature floors, usually through a mixing valve, or whether a new boiler is the better answer. Our boiler repair and installation page covers that side.

Zones and controls

We decide how many zones the house needs and how each one is controlled. More zones give more control and add manifold ports, valves and thermostats.

New build or retrofit

New construction and remodels give open access to the floor. Retrofit work depends on what we can reach from above or below.

Where does radiant floor heat go?

Radiant tubing works in many spaces, and the method changes with the space.

Bathrooms and kitchens

A small zone can warm a tile floor in one room. We check whether the existing boiler can feed that zone.

Basements and garages

Slab floors can carry tubing and turn a cold space into a usable one. The slab, the insulation under it and the heat source decide the design.

Additions and remodels

An open floor during construction is the easiest time to place tubing. We plan the zone and the heat source with the rest of the project.

Whole-home systems

A full radiant system is usually boiler-fed with several zones and a manifold. It gives even, quiet heat with no air blowing.

What are the signs your radiant system needs service?

Any of these means the system needs a look.

  • Floors that stay cold in one room or zone
  • Floors warm in some places and cold in others
  • Clicking, gurgling or rushing water sounds in the loops
  • A boiler that cycles often while the floors stay cool
  • Pressure that keeps dropping, or a relief valve that dumps
  • Water at the manifold, a pump or a valve
  • Heat that takes much longer to arrive than it used to

Repair or replace the radiant system?

Most radiant repairs involve the boiler, pumps, valves and controls, which can be replaced one part at a time.

Usually a repair

  • A failed zone valve, actuator, circulator or mixing valve
  • Air in a loop, or a manifold that needs balancing
  • A failed expansion tank or air separator
  • A boiler problem that a repair or tune-up solves

Usually time to replace

  • A boiler at the end of its life that feeds the floors
  • A manifold that is corroded or leaking beyond repair
  • Controls that are obsolete and cannot be matched
  • Floor loops that leak, which is a larger project we assess on site

We tell you which side your system is on before you spend money. A replacement boiler gets a free written estimate.

Job photos

Hydronic & Radiant Heat: job photos

Real jobs, photographed by the technician who did the work.

Boiler circulator replacement: new green circulator pump on the same piping beside the boiler
Old red circulator pump on rusty iron piping before boiler circulator replacement
Before After
Boiler circulator replacement: new pump on the same piping
Radiant heat replacement: new multi-loop manifolds with a controller board on the same plywood wall
Old radiant manifolds and mixing station on a plywood wall before radiant heat replacement
Before After
Radiant heat replacement: new manifolds on the same wall
Radiant heat installation: new copper piping with a mixing valve and gauge on a basement wall
Radiant heat installation: copper piping with mixing valve
Radiant heating manifold installation: manifold with gauges and PEX loops on a plywood panel
Radiant heating manifold with gauges and PEX loops
Radiant heat installation: copper press piping with a mixing valve and circulator pump
Radiant heat installation: press piping, mixing valve and pump
Radiant heating manifold installation: two-loop manifold with red PEX tubing and blue valves
Radiant heating manifold: two loops with red PEX
Radiant heating manifold installation: black manifold with gray PEX tubing and a circulator pump
Radiant heating manifold with PEX tubing and circulator pump
Baseboard heat repair: burst copper pipe at the end of a finned-tube baseboard heater
Baseboard heat repair: burst copper pipe at a baseboard heater

How does a radiant visit work, and what does it cost?

Diagnostic. Radiant repairs start with a paid diagnostic visit. We check the boiler, pumps, valves, manifold and controls, find the cause and give you the repair price in writing before any work starts.

Estimate. A replacement boiler gets a free written estimate, and so does a new radiant job after a site visit. We do not price radiant work by phone because the floor and the heat loss decide the design.

What to have ready.

  • Which rooms or zones are cold, and since when
  • The boiler’s make and age, or a photo of its label
  • Photos of the manifold and the pumps, if you can reach them
  • For a new job: floor plans, the floor types and whether the space is new or being remodeled

Book online. A non-urgent radiant visit can be booked online: send the form, and we confirm your visit by text. If your heat is out, call 508-521-9477.

Rebates & financing

Mass Save Heat Pump Installer Network participating contractor.

Rebates and the 0% HEAT Loan available.

Financing through Wisetack

Financing for new systems runs through Wisetack via Housecall Pro, subject to credit approval. Estimates on new systems are free.

Recent radiant heating jobs

From our completed jobs, most recent first. Customer names and street addresses are left out.

  • August 2026, Duxbury. Radiant heat system: Replaced the manifold assembly.
  • July 2026, Duxbury. Radiant heat system: Diagnosed zones that were not working properly.
  • March 2026, Lakeville. Radiant heat system: Replaced the mixing valve, the relief valve and the expansion tank.
  • November 2025, Hanson. Radiant heat system: Flushed and balanced the system.

Where do you service radiant heating?

We work in Lakeville, New Bedford, Middleborough, Dartmouth, Fall River, Taunton, Wareham, Brockton, Fairhaven, and the rest of the SouthCoast, South Shore, Cape Cod and Rhode Island. See all service areas.

Brands

Brands we install · Hydronic & Radiant Heat

  • Taco
  • Caleffi
  • Honeywell
  • Uponor
  • Viega
  • Tekmar
Oil boiler tune-up: combustion analyzer connected to the boiler
Keep it running

Add it to a maintenance plan

Seasonal tune-ups keep your boiler efficient and catch small problems before the first freeze.

See maintenance plans

Radiant heating questions, answered

Can radiant floor heat be added to an existing house?

Often yes, but how depends on what we can reach. From below, tubing can go under the subfloor where there is access. From above, it goes into the floor build-up, which raises the floor height. A site visit tells us what is possible.

Is it normal for radiant floors to heat up slowly?

Yes. The floor has to warm before the room does, and a thick slab takes longest. Steady thermostat settings work better than large setbacks.

Does radiant heat need its own boiler?

Not always. Radiant floors run on cooler water than radiators or baseboard, so one boiler can feed both when a mixing valve lowers the temperature for the floors. We check the existing boiler before we recommend a new one.

Do you service radiant systems that another company installed?

Yes. We service boiler-fed radiant systems whoever installed them. Photos of the boiler, the manifold and the pumps help us arrive with the right parts, and you can attach them when you tap Book ASAP.

Can I put radiant heat in just one room?

Often, if the boiler can feed a small zone and we can run the tubing. A site visit tells us what is practical for your floors.

Do you install electric radiant floor heat?

No. Our radiant work is hydronic only, which means boiler-fed heat. If you are choosing between the two, call us and we will talk through your floors.

Do you work on steam boilers?

Yes. Radiant floors run on hot water, and steam is a different system. We service, repair and replace steam boilers and install new ones; see boiler repair and installation.

How much does radiant floor heating cost?

It depends on the area, the floor, the number of zones and the boiler, so we price from a site visit. Our radiant heating cost page explains what moves the price.

Can radiant heat pipes freeze?

Radiant tubing is filled with water or an antifreeze mix, and tubing in an unheated space can freeze and split, especially after a long power outage in a cold snap. Keep the building above freezing, and tell us whether your system has antifreeze in it. If a zone loses pressure or leaks, turn it off at the thermostat and call us, and we pressure test the loops to find the problem. Call 508-521-9477 or tap Book ASAP.

Can a leak in radiant floor heating be repaired?

Often, yes. We pressure test the system to find which loop or connection is losing pressure. A leak at the manifold, a pump or a valve is a straightforward repair, while a leak in tubing under a slab depends on access, and we explain your options before any work starts.

How long does radiant floor heating last?

Equipment life varies with installation, maintenance and operating conditions. The tubing in the floor depends on its material and the quality of the system water, while the boiler, pumps and valves are the parts that wear and get replaced. We advise on repair or replacement after a diagnostic visit.

Is radiant floor heat better than forced air?

Neither is better in every house. Radiant heat gives even warmth from the floor and needs no ducts, but it responds more slowly and the floor covering matters. It can often run off an existing boiler, while forced air makes it easy to add air conditioning, so we choose by the house and by whether you also want cooling.

Radiant heat problem or project?

Schedule radiant heating service in New Bedford & the SouthCoast

Call 508-521-9477, answered 24/7, or tap Book ASAP and the office confirms your visit by text.

Tap to call508-521-9477 Book ASAP
Book ASAP