Skip to content
Licensed & insured Family owned & operated · Lakeville, MA
No heat? Tap to call508-521-9477
Gas boiler installation: wall-hung IBC condensing boiler with new copper piping on a plywood panel
Licensed & insured · Lakeville, MA

Boiler Repair & Installation in New Bedford, Fall River & Southeastern MA

Gas and oil boilers, steam and hot-water systems, baseboard and radiant floors, diagnosed fast and replaced right. Steam and hot-water boilers are common in SouthCoast multi-families, and we work on all of them.

  • Same-day repair
  • Free estimates on new systems
  • Financing through Wisetack
  • Warranty on our labor
Chat with ArmusOnline 24/7 · tap a topic to start

Boiler banging, leaking or not firing? Tell me what's going on.

At a glance

Service area
New Bedford, Fall River, Lakeville, Dartmouth and the rest of the SouthCoast, plus the South Shore, Cape Cod and Rhode Island
Based in
Lakeville, MA. We come to your home or business.
Phone
508-521-9477, answered 24/7
Specialties
Gas, oil and propane boilers, steam and hot-water systems, and radiant floor heat: service, repair, replacement, new installation and tune-ups
Pricing
Repairs start with a paid diagnostic visit. Replacements get a free written estimate.

What boiler and radiant problems do you repair?

We repair gas, oil and propane boilers, steam and hot-water systems, and the radiators, baseboard and radiant floors they feed.

No heat from the boiler

The first checks are power, the thermostat call, the fuel supply and the safety controls, including the limit and the low-water cutoff. A boiler that will not fire is often a failed ignition module or flame sensor on gas, or a clogged nozzle, a primary control or a weak cad cell on oil.

Boiler fires, then shuts off, or cycles on and off

On gas this is often a flame sensor, an igniter or a venting problem, and on oil it is often the primary control or a fouled electrode. Short cycling can also come from an aquastat setting or a zone calling for heat it cannot deliver.

Water on the floor

Water near a boiler can come from the relief valve, a circulator seal, a union or the automatic fill valve, and we trace it before we replace anything. A cracked section in a cast-iron boiler usually means replacement, and a leaking relief valve should never be capped.

Banging, rumbling or kettling

Kettling is scale or sediment on the heat exchanger that makes water flash to steam where it should not. We flush and treat the system and correct the low flow that caused it, and hard well water makes the problem more likely.

Radiators or baseboard stay cold while the boiler is hot

That usually points to the circulator pump, a zone valve that is stuck closed, or air trapped in the loop. We check the pump motor and impeller, test the zone valve motors and purge the air before we replace parts.

Oil boiler lockout, smoke or soot

Oil boilers lock out on the red reset button when the flame is lost, often from a worn nozzle, a dirty filter or a cad cell that has weakened. After the repair we tune the burner and check combustion with an analyzer.

Steam boilers

We service and repair steam boilers, replace them and install new ones, alongside hot-water boilers. Steam systems need a technician who understands near-boiler piping, skimming and the low-water cutoff.

Radiant floors that are cold or uneven

Cold or patchy radiant floors usually come from air in a loop, a stuck mixing valve, a failed circulator or an unbalanced manifold. We check supply temperature and flow at the manifold first, and our radiant heating pages cover these systems in detail.

How do we find the cause?

We start with safety: smells, venting, leaks and the safety controls. Then we test the call for heat, ignition, water flow and temperatures, and on oil boilers we run a combustion analysis.

When do we ask for your approval?

Once the diagnostic is done, we explain what failed and what the fix involves, and we put the price in writing. Nothing more happens until you say yes.

Boilers & hydronic systems we install

Gas boilers

High-efficiency condensing and combi boilers, piped with new near-boiler supply and return lines and an expansion tank.

Oil boilers

Oil boilers repaired, tuned and replaced, or converted to gas with the old tank removed.

Steam & hot-water systems

Steam boilers, radiators and baseboard flushed, bled, balanced and repaired so the far rooms heat as well as the near ones.

Radiant floor heat

Radiant loops for bathrooms, kitchens, basements and additions, run off the boiler you already have or a new one.

Hydronic piping & zoning

Circulators, zone valves, mixing valves and indirect tanks piped cleanly and labeled.

Signs your boiler or radiant system needs service

  • Banging, gurgling or knocking pipes
  • Radiators cold at the top or not heating at all
  • Water on the floor or a dripping relief valve
  • The pressure gauge climbing or dropping
  • No hot water from a boiler-fed coil or indirect tank
  • A burner that won’t stay lit

Repair or replace?

Usually a repair

  • Failed circulator, zone valve, ignitor or control
  • Expansion tank or relief valve problems
  • Sludge and air a flush and bleed will clear
  • A sound heat exchanger with no active leak

Usually time to replace

  • A leaking or cracked section or heat exchanger
  • An oil boiler you want off oil for good
  • Repeat no-heat calls on an aging boiler
  • Adding radiant zones the old boiler can’t carry

We tell you which side your system is on before you spend money, with both options priced in writing.

Job photos

Boilers & Radiant Heat: job photos

Real jobs, photographed by the technician who did the work.

Gas boiler replacement: finished mechanical room with new boiler, zone pumps and an indirect water heater
Gas boiler replacement in progress: mechanical room piping hung and ready before the new boiler was set
During After
Gas boiler replacement: finished mechanical room with the new boiler, zone pumps and indirect tank
Oil boiler replacement: new blue oil boiler with a combustion analyzer attached during startup
Old blue oil boiler with a burner in a block-wall basement before oil boiler replacement
Before After
Oil boiler replacement: new boiler in the same spot, tested with a combustion analyzer at startup
Oil boiler replacement: new green oil boiler with a Beckett burner, expansion tank and copper piping
Old blue oil boiler with a pail and supplies on the basement floor before oil boiler replacement
Before After
Oil boiler replacement: new boiler and near-boiler piping in the same basement
Oil boiler replacement: new green oil boiler with a black Beckett burner and a vent pipe in the same basement
Old blue oil boiler and burner in a cluttered basement before oil boiler replacement
Before After
Oil boiler replacement: new boiler with a Beckett burner in the same basement
Boiler circulator replacement: new green circulator pump on the same piping beside the boiler
Old red circulator pump on rusty iron piping before boiler circulator replacement
Before After
Boiler circulator replacement: new pump on the same piping
Gas boiler replacement: new blue gas boiler and gas water heater installed in the same basement spot
Gas boiler replacement, before: old teal gas boiler and gas water heater with a red pump on the floor
Before After
Gas boiler replacement: new boiler and water heater in the same spot as the old ones
Radiant heat replacement: new multi-loop manifolds with a controller board on the same plywood wall
Old radiant manifolds and mixing station on a plywood wall before radiant heat replacement
Before After
Radiant heat replacement: new manifolds on the same wall
Gas boiler installation: new gray wall-hung condensing boiler with a digital display and copper piping
Gas boiler installation: gray wall-hung condensing boiler
Gas boiler installation: new boiler with copper piping and galvanized vent pipe beside a water heater
Gas boiler installation: new boiler with copper piping and vent pipe
Gas boiler installation: new blue gas boiler with an expansion tank next to a gas water heater
Gas boiler installation: blue boiler with expansion tank
Gas boiler installation: new green gas boiler with a galvanized flue and an expansion tank on top
Gas boiler installation: green boiler with galvanized flue
Gas boiler installation: new gray boiler beside a gas water heater with copper and PVC piping overhead
Gas boiler installation: new boiler beside a gas water heater
Gas boiler installation: new green boiler with circulator pumps, expansion tanks and a gas water heater
Gas boiler installation: new boiler with circulator pumps
Gas boiler installation: inside a new IBC condensing boiler with the cover off during startup
Gas boiler startup: inside a new condensing boiler
Oil boiler installation: new green oil boiler with a black oil burner and new copper piping
Oil boiler installation: new boiler with black burner and copper piping
Oil boiler installation: new green oil boiler with a mixing valve and copper piping, side view
Oil boiler installation: new boiler with mixing valve
Oil boiler installation: copper piping and a mixing valve with gauge beside a new oil burner
Oil boiler installation: copper piping and mixing valve
Oil boiler replacement: new blue oil boiler with a Beckett burner in the same basement
Oil boiler replacement: new boiler with a Beckett burner
Oil boiler installation: new green oil boiler in a tiled utility closet with an expansion tank above
Oil boiler installation: new boiler in a utility closet
Indirect water heater installation: white tank beside a new oil boiler in a basement
Indirect water heater installed with a new oil boiler
Hydronic piping installation: copper main with a balancing valve and an orange motorized actuator in a commercial building
Hydronic piping installation: balancing valve on a commercial main
Radiant heat installation: new copper piping with a mixing valve and gauge on a basement wall
Radiant heat installation: copper piping with mixing valve
Radiant heating manifold installation: manifold with gauges and PEX loops on a plywood panel
Radiant heating manifold with gauges and PEX loops
Radiant heat installation: copper press piping with a mixing valve and circulator pump
Radiant heat installation: press piping, mixing valve and pump
Radiant heating manifold installation: two-loop manifold with red PEX tubing and blue valves
Radiant heating manifold: two loops with red PEX
Radiant heating manifold installation: black manifold with gray PEX tubing and a circulator pump
Radiant heating manifold with PEX tubing and circulator pump
Baseboard heat repair: burst copper pipe at the end of a finned-tube baseboard heater
Baseboard heat repair: burst copper pipe at a baseboard heater

What do you check before recommending a new boiler?

Before we recommend a boiler we check the fuel, the heat loss, the radiators or floor loops, the venting and the controls.

Fuel: gas, oil or propane

We size and install the boiler for the fuel you actually have. If gas is on your street we can quote a conversion too, and we tell you on the first call if it is not.

Size from heat loss

We size the boiler from the house’s heat loss and the radiators or baseboard it feeds, not from the old boiler’s rating. An oversized boiler wastes fuel and short-cycles.

Conventional or condensing

A conventional boiler vents up a chimney, and a condensing boiler captures more heat from the exhaust, vents through PVC and needs a condensate drain. A condensing boiler only condenses when the return water is cool enough, so we look at your radiators before we recommend one.

Steam or hot water

Steam and hot-water systems are not interchangeable, so a replacement has to match the system you have. For steam we also check the near-boiler piping, and we install new steam boilers as well as replacing existing ones.

Combi boiler or indirect tank

A combi boiler heats the house and the hot water in one wall-hung unit, which suits smaller homes with modest hot-water use. For larger households we often pair a boiler with an indirect tank.

Venting and combustion air

We check the chimney or sidewall vent route and the combustion air for the new boiler. Vent terminations that face the water need extra attention near the coast.

Controls and zoning

We look at the zone valves or circulators, the thermostat layout and controls such as outdoor reset that can cut fuel use. Good zoning is part of the comfort you are paying for.

Boiler, heat pump or both

Sometimes a heat pump carries the house for most of the year and the boiler stays as backup for the coldest weather, and sometimes a full switch makes sense. A house with cast-iron radiators and no ducts needs a careful plan, and we price the options in writing.

Commissioning before we leave

Before we leave we set and check pressure, purge the air, check firing and run a combustion analysis. Then we walk you through the controls and the pressure gauge.

Boiler replacement

Replacing a gas, oil or steam boiler starts with a free written estimate. We look at the fuel you have, size the new boiler from the house’s heat loss, and check the venting, the near-boiler piping and the controls before we write anything up. The written estimate includes the permit filing and fee.

New U.S. Boiler V8H oil boiler with Beckett burner, New Bedford MA
New U.S. Boiler V8H oil boiler with Beckett burner, New Bedford MA

If gas is on your street, we can price an oil-to-gas conversion beside a like-for-like swap, and our boiler replacement cost guide explains what moves the cost. Call 508-521-9477 or tap Book ASAP to start.

How does a boiler visit work, and what does it cost?

Diagnostic. Boiler repairs start with a paid diagnostic visit. The technician finds the cause, explains it, and gives you the repair price in writing before any repair work starts.

Estimate. A boiler replacement starts with a free written estimate. We look at the fuel, the heat loss, the radiators or floor loops and the venting, then write up the boiler we recommend and the work included. The written estimate includes the permit filing and fee.

What to have ready.

  • Gas, oil or propane, and the boiler’s age if you know it
  • Steam or hot water, if you know which
  • A photo of the boiler’s label and of the pressure gauge
  • Which rooms or zones are cold, and how long they have been
  • A clear path to the boiler and its shutoff valves

Book online. For a boiler visit that can wait, send the form or call; we confirm your visit by text. If your heat is out, call 508-521-9477.

Rebates & financing

Mass Save Heat Pump Installer Network participating contractor.

Rebates and the 0% HEAT Loan available.

Financing through Wisetack

Financing for new systems runs through Wisetack via Housecall Pro, subject to credit approval. Estimates on new systems are free.

Recent boiler jobs

From our completed jobs, most recent first. Customer names and street addresses are left out.

  • July 2026, Middleborough. Oil boiler: Annual maintenance, done with an AC condenser coil cleaning.
  • May 2026, Fall River. Boiler with baseboard heat: Maintenance and a baseboard leak repair.
  • March 2026, Taunton. Boiler: Removed the old boiler and installed the new one.
  • February 2026, Mattapoisett. Oil boiler: Cleaning and tune-up.
  • February 2026, New Bedford. Oil boiler: Cleaning and tune-up.
  • February 2026, Fairhaven. Hydronic boiler system: Repair and component replacement.

Where do you service boilers?

We work in Lakeville, New Bedford, Middleborough, Dartmouth, Fall River, Taunton, Wareham, Brockton, Fairhaven, and the rest of the SouthCoast, South Shore, Cape Cod and Rhode Island. See all service areas.

Brands

Brands we install · Boilers & Radiant Heat

  • Lochinvar
  • Navien
  • Weil-McLain
  • Bosch
  • Burnham
  • Buderus
  • Viessmann
  • Triangle Tube
  • NTI
  • Peerless
  • Utica
  • Smith Cast Iron
  • Energy Kinetics
  • Baxi
  • HTP
  • IBC
  • U.S. Boiler
  • New Yorker
  • Taco
  • Beckett
  • Riello
Oil boiler tune-up: combustion analyzer connected to the boiler
Keep it running

Add it to a maintenance plan

Seasonal tune-ups keep your boiler efficient and catch small problems before the first freeze.

See maintenance plans

Boiler questions, answered

How can I tell if my boiler needs to be flushed?

Banging or gurgling pipes, radiators that stay cold at the top and rusty water at the drain valve are the usual signs. A flush and bleed is part of our boiler tune-up, and we check the expansion tank and relief valve at the same time.

Can you add radiant floor heat to an older home?

Usually, yes. Radiant floor heat works well in bathrooms, kitchens, basements and additions, and it can run off the boiler you already have. We size the loops and the controls so the rest of the house keeps its heat.

Should I replace my oil boiler with a heat pump?

Often, yes. A cold-climate heat pump lowers heating costs in many SouthCoast homes and qualifies for rebates, but insulation and electrical service matter, so we compare it with keeping or converting the boiler first.

Can you convert my oil boiler to gas?

Often. We confirm with the gas utility whether a service line can reach the house, then quote the boiler, gas piping, permits and old-tank removal as one price.

My boiler relief valve is leaking. Can I cap it?

No. Never cap or plug a relief valve: it is the safety that keeps the boiler from building dangerous pressure. A dripping relief valve means the pressure is too high or the valve has failed, so call 508-521-9477 and we will find the cause.

Why is one zone cold when the rest of the house heats?

Usually a zone valve or a circulator. When the valve or the pump on that zone fails, hot water never reaches it. Both are common repairs.

What does low boiler pressure mean?

Low pressure on the gauge often points to a leak, the fill valve or a waterlogged expansion tank. We check the expansion tank and relief valve during every boiler tune-up.

What does an annual boiler tune-up include?

A flush and bleed, a check of the expansion tank and relief valve, and a combustion analysis to confirm the burner runs safely and efficiently.

Do boiler replacements need a permit in Massachusetts?

Yes. A boiler replacement in Massachusetts needs the required permits and inspections, and the permit filing and fee are included in the written estimate.

What rebates and financing are available?

Mass Save Heat Pump Installer Network participating contractor. Rebates and the 0% HEAT Loan available. We confirm eligibility and file the paperwork. Financing for new systems runs through Wisetack via Housecall Pro, subject to credit approval.

My boiler stopped. What can I check before I call?

Check four things, then call if it still will not run. Make sure the thermostat is set to heat, the red emergency switch near the boiler or at the top of the basement stairs has not been flipped off, the oil tank has oil or the gas supply is on, and the pressure gauge on a hot-water boiler is not reading near zero. If your oil burner has a red reset button, press it no more than once, and never cap or plug a relief valve. Then call 508-521-9477.

How long does a boiler last?

A well-maintained cast-iron boiler can run 20 to 30 years or longer. Condensing boilers often last 15 to 20 years because their heat exchangers are thinner. Annual service, good water chemistry and correct sizing matter more than the brand name.

How much does boiler repair cost?

It depends on the cause, the fuel (gas, oil or steam) and how easy the boiler is to reach: a failed valve or circulator is a smaller job than a part inside the boiler. We do not quote repair prices by phone, so call 508-521-9477 to set up the visit; the repair price comes to you in writing before any repair work starts. Repairs: paid diagnostic visit. Replacements: free written estimate.

Is it safe to keep running my boiler if it shows an error code?

Write down the code and the boiler brand, and do not keep resetting it, because a lockout code means a safety control stopped the boiler for a reason. If you smell gas or a carbon monoxide alarm sounds, leave the building and call 911 or your gas company from outside, then call us. If water is leaking, switch the boiler off at the red emergency switch when it is safe to reach. Otherwise call 508-521-9477, answered 24/7, or tap Book ASAP.

How do I reset my boiler?

Check the simple things first: the thermostat is calling for heat, the red emergency switch is on, the pressure gauge on a hot-water boiler is not near zero, and there is oil in the tank or gas to the boiler. An oil boiler has a red reset button on the burner that you may press once. If the boiler locks out again, stop there, because a repeat lockout means something needs finding. Do not add water or touch the relief valve; call 508-521-9477 or tap Book ASAP.

Why is my radiator cold at the bottom?

A radiator that is cold at the bottom usually has sludge or scale restricting the flow. A stuck radiator valve or a weak circulator or zone valve can do the same, and trapped air is the usual cause when the top is the cold part. We check the pump and the zone valves, then bleed or flush the system as needed. Call 508-521-9477 or tap Book ASAP.

Why is my boiler pilot light out?

A gas boiler with a standing pilot can lose it to a failing thermocouple, a dirty pilot assembly, a draft or a gas supply problem, and many newer boilers have no standing pilot at all. If you smell gas, leave the building and call your gas company or 911 from outside, then call us. If the pilot keeps going out, we test the thermocouple, the pilot and the gas valve on a repair visit. Call 508-521-9477 or tap Book ASAP.

Why does my steam boiler keep shutting off?

On a steam boiler the low-water cutoff shuts the boiler off to protect it. The cause can be low water from a leak, a blocked gauge glass or cutoff, sediment in the cutoff, or a pressure control fault. We check the water level, the cutoff and the return piping, and the cutoff should never be bypassed. Call 508-521-9477 or tap Book ASAP.

Boiler problem?

Schedule boiler service in New Bedford & the SouthCoast

Call 508-521-9477, answered 24/7, or tap Book ASAP and the office confirms your visit by text.

Tap to call508-521-9477 Book ASAP
Book ASAP